SCAT VW- Special Tools

SCAT BORING/FLY CUTTER TOOL ASSEMBLY • Versatile & inexpensive • Special Professional tool designed to bore cases & heads for oversize cylinders & pistons or fly-cut heads for increased compression • Tool may be used with mill, drill press, or hand drill • Ring base of tool housing eliminates necessity of milling head surfaces to use tool • 356 T6 Aircraft Quality Aluminum Housing machined to exacting tolerances with a Gits oil fitting to lubricate the 1 1/2" diameter precision ground steel shaft • 3/4" x 1 1/4" Steel Tool Holder & Centering Block are precision machined to insure accuracy • Precision machined tool steel cutter • Steel components are black oxide finished to insure long corrosion resistant use • Illustrated instructions & all necessary hardware is included PART NO. DESCRIPTION PRICE 98016 Complete Tool: Assembly $345 98034 Replacement Components: 1.312" Replacement Cutter-use with #98041 Holder only $26 98041 Replacement Components: Tool Holder with Screws $30 BENCH & FLOOR MODEL VW ENGINE STANDS • Professional model engine stands allows you to work on your VW or Porsche engine & transaxles at the proper height & angle with ease • Twist of "T" handle allows you to rotate a full 360 degrees • Heavy duty steel construction - strong durable casters provide mobility for floor model stand • Ears of engine stand yoke bolt to case of transaxle housing PART NO. DESCRIPTION PRICE 98001 Bench Model Engine Stand $28 98079 Floor Model Engine Stand - UPS Shipable $82 CRANK & FLYWHEEL DRILL JIG • For adding 4 dowel pins in crank & flywheel with SPG offset dowel pattern - same as all performance aftermarket crankshafts PART NO. DESCRIPTION PRICE 98015 CRANK & FLYWHEEL DRILL JIG $58 CRANKSHAFT GEAR PULLER • Remove timing gear from crankshaft without damage - use of press is not required PART NO. DESCRIPTION PRICE 98057 CRANKSHAFT GEAR PULLER $97 END PLAY MEASURING TOOL • Measure end play movement of VW crank without use of dial indicator - for use with feeler gauge - All VW, Porsche 912 & 914 PART NO. DESCRIPTION PRICE 98086 END PLAY MEASURING TOOL $22 VW FLYWHEEL SEAL INSTALLER • Accurately presses rear main flywheel seal into engine case - clears all dowel pins Use with all Type 1-3 VW engines PART NO. DESCRIPTION PRICE 98095 VW FLYWHEEL SEAL INSTALLER $27 VW FLYWHEEL LOCK • Locks flywheel securely in position - for use with 109 tooth 6V or 130 tooth 12V flywheels PART NO. DESCRIPTION PRICE 98072 VW FLYWHEEL LOCK $10 PISTON RING COMPRESSOR • Tool compresses piston rings using pliers allowing cylinder to be slipped over piston PART NO. DESCRIPTION PRICE 98092 83-87MM $10 98093 88-94MM $10 VW VALVE LIFTER RETAINING CLIPS • Designed to hold valve lifters in place during assembly or disassembly of engine • Use with All Type 1-3 VW engines PART NO. DESCRIPTION PRICE 98088 VW VALVE LIFTER RETAINING CLIPS $10 VW DECK HEIGHT MEASURING TOOL • Accurately measures distance from top of cylinder to top of piston • For use with All Type 1-3 VW engines PART NO. DESCRIPTION PRICE 98081 VW DECK HEIGHT MEASURING TOOL $37 VW SPRING REMOVAL TOOL • Remove valve springs on assembled or disassembled engines • Includes fitting to pressure combustion chamber to hold valves closed - Use on all VW 40HP & later engines PART NO. DESCRIPTION PRICE 98082 VW SPRING REMOVAL TOOL $69 VW/PORSCHE STEEL CLUTCH PILOT • Aligns clutch disc with pressure plate and flywheel for ease & proper installation PART NO. DESCRIPTION PRICE 98056 VW/PORSCHE STEEL CLUTCH PILOT $10 VW VALVE GUIDE INSTALLER • Use to install 8mm VW valve guides - for use on both air & water cooled VW heads PART NO. DESCRIPTION PRICE 98100 VW VALVE GUIDE INSTALLER $22 VALVE STEM SEAL INSTALLATION TOOL • Use to install stock or aftermarket type seals - allows seal installation with valve in place PART NO. DESCRIPTION PRICE 98101 VALVE STEM SEAL INSTALLATION TOOL $26 DISTRIBUTOR DRIVE PULLER • Easy removal & installation of distributor drive pinion PART NO. DESCRIPTION PRICE 98087 DISTRIBUTOR DRIVE PULLER $39 OIL PUMP PULLER • Oil pump removal without damage to pump or engine case PART NO. DESCRIPTION PRICE 98078 OIL PUMP PULLER $9 VW OIL PRESSURE PISTON PULLER • For simple removal of oil pressure piston from engine case - All VW Type 1-4 engines PART NO. DESCRIPTION PRICE 98089 VW OIL PRESSURE PISTON PULLER $39 AXLE NUT REMOVAL TOOL • For use in removal of rear axle nut - use with 1/2" breaker bar PART NO. DESCRIPTION PRICE 98083 36MM $18 98084 46MM $18